- Brand: OXILAM
- Light Source Type: LED
- Color Temperature: 6000 Kelvin
- Brightness: 4000 Lumen
- Wattage: 8 watts
- 【600% Brightness Improved】 Full 360-degree illumination with a projector-style lens, and equipped with 26 PCS 3020 SMD LED chipsets, OXILAM 7443 led brake light bulbs are 5 times brighter than halogen, producing bright red light to keep a distance between vehicles and more effective warning
- 【No Worry for CANBUS Error Issue】 Compatible for both CK/SRCK and standard socket, and fits for 95% vehicle’s computer system. For some sensitive models, if you meet flicker/error issue, don’t worry. This is normal and could be solved by load resistors. Also, this problem may occur when multiple pairs of this bulb are installed at the same time. Please LET US KNOW and we will provide load resistor or other solutions to minimize the inconvenience to you.
- 【Multi Application】OXILAM 7444 led bulb is commonly used for brake lights, tail lights, stop lights, turn signal lights, parking lights. Fits for 992, 7440, 7441, 7443, 7444, W21W, WY21W, 7440NA, 7440NAK, 7444NA, 7444NAK, 7443LL, T20, etc. With instant start capability and no warm-up time.
- 【60,000Hr Long Lifespan】OXILAM 7440 led bulbs are made of aircraft grade aluminum body and unique bump appearance which effectively pull the heat away from the LED chips, provide up to 60,000 hours continuous lighting, No more frequent changes improved driving experience
- 【Product Specification】Voltage: DC 12V, High Power: 8w/bulb (Other leds on the market are 4 to 6w/bulb), Size: 2.16 x 0.79 x 0.79 inch, Lumen: 4000lm/pair, Color: Brilliant Red NOTE: Amazon filter system may not be 100% accurate or up to date, please check your vehicles owner’s manual or the original bulb to confirm the correct bulb size you need before placing the order

























Roger K. –
Bright led lights, did not seat properly due to raised tabs and the internal resistor does not work. 2016 Nissan Maxima hyper flash.Update:Seller contacted me and immediately sent out the load resistors. After installing the resistors only to the back turn signals, this corrected the hyper flash. No instructions are included so look up on YouTube. Do not cut your wires, the resistors need to bridge from positive to negative, splicing into both wires.
Amazon Customer –
I went to Honda dealer today because I lost my car’s brake lights after the last service a few weeks ago. I did not realize that it was not working until other drivers’ telling me that my brake lights is not working. So, I went back to Honda & I was informed by the service guy it just needs new lights. So, I gave this one that I purchased from Amazon. It’s very bright & clear and it was install for free in no less than 7 minutes. Highly recommend.
Amazon Customer –
I replaced the break light bulb as well as the rear turn signal bulb on my 2022 Tacoma – they are very bright. However, it causes the front and rear turn signal to rapidly flash as if the vehicle doesn’t recognize the bulb or thinks the bulb is burnt out – so it flashes extremely fast. Is there a reset or something I have to do now?
Ricardo Andrade –
Very happy with the brightness of the lights but unfortunately on my 2019 Silverado 1500 is has rapid flash after the first two blinks. Other than the error message and rapid flag I get I do recommend.
Freddy –
good quality my bulbs started to HF so I contacted the seller they sent me resistors right away, I bought 2 sets 1 for my stoplights and second set I wanted red turn signals not amber they work great only issue is the color if you put it in a clear turn signal the color is closer to pink than red I’ll probably use these on my second car for stop lights.
William Turner –
Bought these for my 2017 Chevy Suburban because I’m switching everything over to LED so I did a little research and discovered there are some bulbs that are “error free” and some bulbs that aren’t. I didn’t want to buy load resistors so I bought these bulbs because they were advertised as error free, but when I installed them, it shows a turn signal error and hyper flashes. Also, they were very hard to get in the socket. They aren’t built exactly like the 7440s that came out of it and I had to press extremely hard to get them seated all the way. The bulbs are very bright and they all worked but they are not error free so I’m going to have to wind up buying load resistors anyways. I filtered the results for things that were supposed to fit my vehicle to avoid getting bulbs that don’t fit and although I did get them in, they don’t fit the way they are supposed to.
Justin Raymer –
The media could not be loaded. I bought these based on the advertised no hyper flash.If you install them on a third gen Tacoma, everything will be fine and you will not get a hyper flash, until you turn the headlights on. Daytime driving will result in no hyper flash but as soon as you turn on the headlights they will.You need 4 total (2 per tail light) I have tried all combinations of bulbs and types to get them to not flash. It doesn’t matter. I have mixed incandescent with the LED, ran all LED, put the incandescent for the flash and led for the stop. Doesn’t matter.As an actual LED bulb, they are super bright and cast a good light pattern. The three-star rating reflects the advertised no hyper flash bulb that does indeed hyper flash.
Amazon Customer –
This item works on corolla 2011.