- Brand: Nilight
- Color: Red, White, Black
- Vehicle Service Type: Truck, Pickup Truck, Tractor, Trailer
- Voltage: 12 Volts
- Light Source Type: LED
- Position: Right
- Cover Included: 2PCS Submersible Trailer Light Kit
- Fit Type: Universal Fit
- Material: Stainless Steel
- Water Resistance Level: Waterproof
- Multi-functions: Combined functions of tail, brake/turn signals, side marker, license plate light. Perfect for 12V DC vehicles with a maximum width of 80 inches. Such as most of trailers, boats, trucks, RV, Marine, Pickups, camper, tractors etc
- Excellent Brightness: Left lamp has 27 diodes including 9 diodes for license plate light, right lamp has 12 diodes. Quality LEDs draw less amperage but outputs optimal brightness, improving great visibility and extend longer lifetime than the incandescent lamp. DOT Compliance to ensure your 100% safety
- Entirely Submersible: The inside LEDs and circuit board is fully waterproof sealed to work under water perfectly without electric short risk. The light housing also features water drainage for added protection
- All-in-one Kit: Comes with everything for your straightforward installation of the light, include lights, license plate bracket, 25ft length trailer wiring harness and the different types of stainless steel mounting hardware
- Easy Installation: For light mounting: Lamp with license plate light on the left side, the other on the right side. For wiring routing: Please see Picture 5 for instruction. For wiring connection: Just color to color, white to the ground (vehicle frame). For hardware you might need to use, please see Pic 8 for instruction
- Fit Type: Universal


![Deals ✔️ 2pc 6" Red Oval LED Trailer Tail Light Kit [DOT FMVSS 108] [SAE S2TSI6P2] [Grommet & Plug Included] [IP67 Waterproof] [Stop Turn Tail] Trailer Brake Lights For Boat Trailer RV Trucks ⌛ 2 Deals ✔️ 2pc 6" Red Oval LED Trailer Tail Light Kit [DOT FMVSS 108] [SAE S2TSI6P2] [Grommet & Plug Included] [IP67 Waterproof] [Stop Turn Tail] Trailer Brake Lights For Boat Trailer RV Trucks ⌛ -Govee-shop 51iHNf2xN2L](https://www.headlight-store.com/wp-content/uploads/2022/12/51iHNf2xN2L-100x100.webp)


























Abubaca –
The trailer lights come with three machine threaded inserts. These inserts match up with the holes on the trailer light brackets. The right trailer light had one insert that wasn’t the same as the others. Since I couldn’t find anything in my scrounge pile to thread into it I had to drill a hole in my light bracket. Also, instead of using a bolt to thread into the light assembly, it just uses a small piece of all-thread about 1.25″ long. So, I put the all thread in with super glue and used three nuts to get them in snug to the light assembly.If you’re expecting an extremely user friendly experience you may be disappointed. If you have skills, you’ll be fine. The lights themselves do appear to be water tight. The wiring on the inside of the light is potted and the tail light assembly is one enclosure so it should maintain it’s watertight integrity. They are extremely bright.
kayaked –
Lights were easy to install. I’m reserving my water resistant rating until I launch my boat again. All my boat use is in salt water which causes lots of corrosion problems for trailers and boats. So if these lights don’t leak (unlike the original water proof lights which did leak and were ruined by salt water corrosion) I will update the Water Resistance rating for this product.
Thomas K –
These trailer lights perfectly aligned and bolted onto existing brackets on my Bayliner boat trailer. The light housings seem molded from a fairly brittle plastic when compared to the tough, resilient OEM light housings. I didn’t detect any water intrusion in the housings after being submerged while launching my boat, but I doubt that the lights will hold up over time. I did not use the included wire connectors, which are not sealed. Instead, I purchased Solder Seal Heat Shrink Butt Connectors on Amazon (https://smile.amazon.com/dp/B07PXJ6S11?psc=1&ref=ppx_yo2ov_dt_b_product_details), which are waterproof, easily installed, and worked great. The license plate bracket is molded from the same brittle plastic as the light housings, and the bracket broke off (along with my license plate) at some point during my first trip. Lesson learned: use the lights, scrap the license plate bracket. For the low price, these lights are a good buy.
Cory –
They work good and they look good. What I like best about them is that they’re bright but not blinding bright like some you see on the road. Highly recommend these.
Brandon Lloyd –
They were inexpensive so I wasn’t expecting much. I was wrong. Great quality product
Bertwin H. Butterfield –
Used for lights on my bike rack for e-bikes
Raymond P. Zaworski –
Nice equipment, the anchor lugs could be longer, and more locking nuts would be great, had to purchase both of these to attach item to my scooter hauler.
Amazon Customer –
This product was Very easy to instal. The lights fit very well on my boat trailer. These are nice and bright, Just what I was looking for.